7
DIGITAL VIDEO MOTION DETECTION
Number of Channels: 16.
Sensing Area: Programmable 16 × 12 block array.
Variable sensing area can be as small
as 1 block. Programmable sensitivity
level.
Active
Video Recording: Channels detecting activity may be
programmed to record more frequently
than channels without activity.
Live Video
Display Update: Frequency of update of live video dis-
play depends on level of activity in
front of camera.
Museum Search: Upon video playback, a programma-
ble search block array may be set
and searched for motion at an accel-
erated rate.
AUDIO
Number of
Audio Channels: 1.
Audio Capability: Audio can be enabled to record con-
tinuously onto the hard drive as an
independent source in synchronization
with the multi-channel video.
Audio Input: Rear panel jack requires an external
powered microphone input via a
3.5 mm phono type plug and
maximum input of 1.5 volts rms.
Audio Output: Front and rear panel jack requires an
external speaker or mono headphone
output via a 3.5 mm phono type plug
of impedance 8 ohms and maximum
handling power of 1 watt.
Audio Quality: Speech quality, based on
TrueSpeech™ 8.5 compression.
Audio
Frequency Response
(Input/Output): 200 to 3400 Hz, based on an audio
frequency digital sampling rate of
approximately 8000 8-bit samples
per second
Audio Dynamic Range
(Input/Output): 84 dB, based on an audio dynamic
range digital sampling rate of
approximately 8000 14-bit samples
per second.
COMMUNICATIONS
Protocol: RS-232, RS-422 and RS-485
(AurorANet).
Ports: COM1 and/or COM2 configured via
menus, jumpers and/or AurorANet
termination box.
Control Hardware: Can be remotely controlled via an
AUR2K-KBD keyboard, an
AurorA2000 multiplexer or another
AurorAcorD unit using AurorANet.
Software Upload: Can be uploaded directly with software
upgrades via COM1 or COM2 using
Microsoft Windows Hyperterminal™.
MECHANICAL PTZ (TELEMETRY) MODE
Functions: Pan.
Left/Right.
Tilt Up/Down.
Pan/Tilt Speed.
Autopan.
Zoom In/Out.
Iris Close/Open.
Autoiris.
Lens Speed.
Focus Far/Near.
Digital Zoom.
Acknowledge Alarm.
Auxiliary Devices On/Off.
Preset Store/Recall.
Freeze/Restore Video.
Help Screen.
Connection: COM1 and/or COM2 configured via
menus and jumpers using RS-422
protocol.
Maximum Number
of Receivers: 16.
ALARM OPERATION
Number of Hardwired
Alarm Inputs: 16. Each of these can be set as an
output.
Hardwired Alarm
Input Type: Alarm equipment connected to
AurorAcorD inputs through the provid-
ed DB-37 connector. Should provide
voltage-free contact pairs or the
equivalent as the output.
Alarm Outputs: 2 dry-contact relay outputs, one nor-
mally closed (NC) and one normally
open (NO). Relay is rated at 0.5 A at
42 V with a resistive (noninductive)
load.
Aux Alarm Output: TTL active high or low.
Alarm
Recording Modes: 1. Normal recording continues
unchanged.
2. Alternate recording provides
increased frequency of alarmed
cameras. Non-alarmed cameras
continue to be recorded.
Video Loss: Alarm is generated when loss of
video is detected.
TITLING
Camera ID: A default camera title with number is
displayed unless replaced by a cus-
tomer-selected title.
Alphanumeric Titling: Each title may have up to 12 alphanu-
meric characters. Size, color, shadow,
and background are selectable.
Screen Display: The screen may display various com-
binations of title, time/date, mode,
status, and various messages.
Recorded Information: Camera title, time, date, plus alarm
information are recorded with each
image.
Technical Information (cont’d)
Model No: Product Code:
Refer to Table 1 Refer to Table 1
SPEC: V091 REV: 402
Vicon Product Facts
SEC: 4
(11 stránky)
(112 stránky)
(2 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce